In India, three-wheelers are one of the most convenient and affordable ways of transportation. They not only let you cross small distances quickly, but they also save you money on gas. While reading it, there is a sensation of excitement and comfort. If you’re a three-wheeler enthusiast, you should be familiar with the various components of your all-weather friend on the road.
However, few people are well-versed with the vital components found in any three-wheeler. This post is for you if you’re one of those people. Engine, gear, clutch, accelerator, brakes, tyres, fuel tank, and exhaust pipe are the basic three-wheeler spare parts listed and detailed here. Continue reading to find out about them in detail.
-
Engine
The vehicle’s main source of power is the engine. The engine generates mechanical power by burning gasoline.
Mechanical energy is created by converting chemical energy. Before the twentieth century, the fuel was burned or combusted outside the physical engine. The fuel, which was frequently coal, was burned to generate heat. This heat was then used to make steam by boiling water. The steam was pre-heated before being injected into the engine, where it pushed the piston down into the cylinder. This is referred to as an External Combustion Engine (ECE) or a steam engine in the past.
The Internal Combustion Engine, used in today’s vehicles, is a type of engine in which the fuel is burned directly inside the vehicle. The air/fuel mixture expands fast as it burns, increasing the pressure inside the cylinder. This rise in pressure pulls the pistons down the cylinder, turning the crankshaft and giving us a continuous rotational motion to move the three-wheeler and other components.
-
Brakes
One of the most critical parts of a three-wheeler is the brakes. They are used to slow down the vehicle. Disc brakes and drum brakes are the two types of brakes available. When you come to a complete stop in a moving vehicle, you must use the brakes. The primary function of the brake system in a 3-wheeler is to slow down or decelerate a vehicle. The brake pads compress against the rotor attached to the wheel when you step on the brake pedal, causing the car to slow down owing to friction.
-
Tyres
A vehicle’s tyres act as a barrier between it and the road. Every “three-wheeler” comes with three tyres, as the name says. Tubeless tyres and tube tyres are the two types of tyres. To maintain proper grip and contact with the road, different thread patterns are constructed on the surface of a tyre. Keep in mind that tyre pressure should be maintained at all times. It will assist you in maintaining vehicle balance and improving fuel efficiency. They must also be replaced regularly.
-
Clutch and Accessories
A vehicle’s clutch and gear are a collection of components that are unique to it. The clutch is used to apply brakes and change gears during the ride, while the gear is utilised to manage motion and torque. Gears are typically displayed as a lever that the rider can operate with his or her left leg. The clutch and gears of a car, like other mechanical parts, should be repaired regularly. The clutch should be adjusted to provide the freest play possible. An over-tightened clutch can make it harder to ride and lower the vehicle’s fuel economy.
-
Exhaust Pipe
The exhaust system’s job is to keep harmful gases out of the vehicle, prevent people from becoming ill, and reduce exhaust noise. The exhaust system comprises several pipes and components that allow exhaust gases to escape the engine beneath the car.
-
Accelerator
The accelerator is another important part of any three-wheeler. The gas pedal is another name for the accelerator. It’s the pedal on the far right side of the floor. This pedal regulates the amount of gas supplied into the engine and, as a result, the vehicle’s speed.
-
Fuel Tank
The function of a fuel tank is to hold fuel, as the name suggests. The gasoline tank volume differs from one vehicle to the next. The fuel tank has a cap on top to saturate it with gasoline. Typically, the gasoline tank is situated above the engine.
The fuel tank should be cleaned regularly to avoid the formation of rust, which can react dangerously with fuel. Your 3-wheeler’s gasoline tank can be cleaned using baking soda or white vinegar.
-
Headlamp and Tail-lamp
A three-head wheeler’s lamp and tail lamp are lights that aid the rider and others on the road. The headlamp, often known as the vehicle’s eye, is placed in front of the three-wheeler and is intended to provide clear visibility of the road and other vehicles at night or in foggy situations. On the other hand, the taillight is situated on the back of the three-wheeler so that other cars on the road can quickly identify your bike and keep a safe distance.
If you own a three-wheeler or plan to get one in the future, you should be familiar with the following common three-wheeler parts. Getting your vehicle serviced regularly will help you keep it in great shape.
Fargo AutoElecctricals offers a comprehensive range of high-quality products sourced from OEM as well as other smaller companies to provide solutions for passenger and loading 3-Wheelers from Bajaj, Piaggio APE, Mahindra, Force Motors, Vikram, Atul, and other Indian companies running on various energy sources such as Diesel, Petrol, CNG, and Electricity.
Please feel free to contact us if you have any questions. Or you can visit our website (https://fargoautoelectricals.com/meters.html) for more details.
Our products are also available on Amazon, Flipkart, and many e-commerce sites to make it easy for you.
Brands Available with Us-
- Uno Minda
- Veethree Instruments
- Lucas-TVS Limited
- BOSCH
- Kamei AutoElectrik
- Varroc
- Pavna